ZRKH - RK11 / RK05F/J performance exerciser

	ABSTRACT:
		Multi-disk exerciser. Begins by a serie of tests aimed at detecting failures associated with boundary condition transfers,
		latter part is the exerciser.

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 8K memory, RK11, 1 to 8 drives

	SOFTWARE:
		RK11	basic tests
		RK05	dynamic tests
		RK05	utility package (if needed)

	OPERATING PROCEDURES:
		200 start program
		210 restart address, go straight to exerciser
		- load program, start 200

	SWITCH SETTINGS:
		SW 15   -  halt program on error
		SW 13   -  inhibit error print-out
		SW 12   -  type out error history
		SW 11   -  dump out all RK11 registers
		SW 10   -  bell on error
		SW 09   -  loop on error
		SW 08   -  dump out transfer data and error statistics
		SW 06   -  select bus address limits for data transfer
		SW 05   -  halt before doing the next set of commands
		SW 04   -  do not rewrite the disk when restarting at 210
		SW 03   -  type out elapsed time at error
		SW 02   -  drop after maximum error
		SW 01   -  type serial number of erroring drive
		SW 00   -  type only elapsed time if SW8 and SW3 = 1
			
	RUNTIME:
		30 to 90 minutes for 1 pass.

ZRKI - RK11 / RK05F/J utility package

	ABSTRACT:
		- compatibility package
		- oscillating seek package
		- formatter-surface verifier
		- control panel test
		- head alignment routine
		- power fail test

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 8K memory, RK11, 1 to 8 drives

	SOFTWARE:
		This is not a diagnostic. It assumes that all equipment is functional.

	OPERATING PROCEDURES:
		200 start program
		- load program, start 200

	SWITCH SETTINGS: none, use it as directed by the program

ZRKJ - RK11 / RK05F/J basic logic test #1

	ABSTRACT:
		- checks basic logic of the RK controller
		- part #1 tests only drive independent logic of the controller

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 8K memory, RK11

	SOFTWARE:
		No MAINDEC has to be run before.

	OPERATING PROCEDURES:
		200 start program
		- load program, start 200
		- put drive in load as a precaution

	SWITCH SETTINGS:
		SW 15   -  halt program on error
		SW 14   -  loop on test
		SW 13   -  inhibit error print-out
		SW 12   -  cycle on error to the previous scope statement
		SW 11   -  inhibit iteration
		SW 10   -  testing on simulator
		SW 09   -  loop on error
		SW 08   -  loop on test as per SW 7-0
			
	RUNTIME:
		1 minute on 11/20. Less for faster machines.

ZRKK - RK11 / RK05F/J basic logic test #2

	ABSTRACT:
		Checks basic logic of the RK controller
		Part #2 if used with a drive is able to detect faults in that drive also.

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 8K memory, RK11, 1 to 8 drives or the RK05 simulator

	SOFTWARE:
		The following MAINDECs should be run successfully before: RK11 basic logic test part #1.

	OPERATING PROCEDURES:
		200 start program
		- load program, start 200
		- DRIVES TO BE TESTED?  0,1,2 <CR>
					0,1,2F,4 <CR>

	SWITCH SETTINGS:
		SW 15   -  halt program on error
		SW 14   -  loop on test
		SW 13   -  inhibit error print-out
		SW 12   -  cycle on error to the previous scope statement
		SW 11   -  inhibit iteration
		SW 10   -  testing on simulator
		SW 09   -  loop on error
		SW 08   -  loop on test as per SW 7-0
		SW 06   -  drop the drive after maximum number of errors
			
	RUNTIME:
		2 minutes on 11/20. Less for faster machines.

ZRKL - RK11 / RK05F/J dynamic test

	ABSTRACT:
		Demonstrate the electromechanical integrity of the drive.
		Checks linear positioner control and speed control.
		Verifies read-write logic integrity.
		Provides a timer for the seek function.

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 8K memory, RK11, 1 to 8 drives

	SOFTWARE:
		The following MAINDECs should be run successfully before: RK11 basic logic test part #1 and part #2.

	OPERATING PROCEDURES:
		200 start program
		210 conversational mode
		- load program, start 200

	SWITCH SETTINGS:
		SW 15   -  halt program on error
		SW 14   -  loop on test
		SW 13   -  inhibit error print-out
		SW 12   -  cycle on error to the previous scope statement
		SW 11   -  dump all RK11 registers on error
		SW 10   -  bell on error
		SW 09   -  loop on error
		SW 08   -  loop on test indicated by user
		SW 06   -  type seek timer
		SW 05   -  type the graphs
		SW 04   -  type the complete graph
		SW 03   -  terminate function selected by user
		SW 02   -  drop drive after maximum number of errors
		SW 00   -  ask for pattern
			
	RUNTIME:
		5 minutes on 11/20.