ZTMA - TS03/TE/TU10 instruction test

	ABSTRACT:
		This test will test all registers, tape motion, data transfers, extended memory and (if selected) manual intervention test.

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 4KW of memory, TMB11 control unit and one TS03 tape unit

	OPERATING PROCEDURES:
		200 start/restart program
		- load program into memory
		- place one tape unit on-line at loadpoint, write enabled, unit 0 selected
		- load address 200
		- clear console switches
		- press start
		- program will type "SET SW0 = 1 IF 7 CHANNEL"
		- if 7 channel-drive set SW0, press CONTINUE

	SWITCH SETTINGS:
		SW 15=1   (100000)   halt on error
		SW 14=1   ( 40000)   scope loop
		SW 13=1   ( 20000)   inhibit error type out
		SW 12=1   ( 10000)   inhibit subtest iteration
		SW 11=1   (  4000)   single pass
		SW 10=1   (  2000)   inhibit manual intervention test
		SW 09=1   (  1000)   TS 03 tape drive
		SW 00=1   (     1)   7 channel tape unit

	RUN TIME:
		Without manual intervention test, 1 minute.

	NOTES:
		Error printouts have this layout:

			PC STATUS COMMAND BYTE CA DATAB READL TEMP CRCCAL

ZTMH - TS03/TE/TU10 multidrive data reliability exercise

	ABSTRACT:
		This program will test all tape drive functions such as write, read, rewind, tape positioning,
		EOT - BOT sensing and assumes a good controller.

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 8KW of memory, TMB11 control unit and 1-8 TS03 tape units

	OPERATING PROCEDURES:
		start/restart addresses:
		200 initial start, all parameters
		204 restart, last pattern used
		210 restart, original pattern
		240 auto sequence mode
		- load program into memory and start program (200 or 240)
		- set desired switches
		- load address 200
		- answer the questions:

			register start= 172520
			vector address= 224
			unit number= (0-7)
			density= (0-3)     (3=800BPI, 9CH)
			parity= (0 or 1)
			unit number= (0-7)
			record count=100 (1-177777)
			character count= 200 (4-4000)
			pattern number= 1 (0-20)
			tape mark= 0 (0 or 1)
			single pass= (0 or 1)
			enter stalls
			        read= 1             }
			        write= 1            } each incr. is about
			        turn around=1  }   2,6 µSec.

	SWITCH SETTINGS:
		SW 15=1   (100000)   halt on error
		SW 14=1   ( 40000)   yozzle on current block
		SW 13=1   ( 20000)   do not check data errors
		SW 12=1   ( 10000)   do not check write status
		SW 11=1   (  4000)   do not check read status err.
		SW 10=1   (  2000)   do not print errors
		SW 09=1   (  1000)   rewind all tapes
		SW 08=1   (   400)   random data
		SW 07=1   (   200)   random character count
		SW 06=1   (   100)   random record count
		SW 05=1   (    40)   yozzle current record
		SW 04=1   (    20)   print statistics
		SW 03=1   (    10)   do not read
		SW 02=1   (     4)   N/A
		SW 01=1   (     2)   disable retries
		SW 00=1   (     1)   do not write

	NOTES:
		Recommended switch setting SW 6, 7, 8 = 1 to randomize test.

ZTSE - TS03/TMA11/TMB11 drive function timer

	ABSTRACT:
		This test assists in testing the controller and the tape drive.
		Operations are executed and timed. There is no limit or error testing facilities.
		The decision on the validity of times measured must be made by the operator.

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 4KW of memory,
		TMB11 control unit and 1-2 TS03 tape units

	OPERATING PROCEDURES:
		200 start/restart program
		- load program into memory
		- set desired TS03 on-line
		- load address 200
		- press start
		- enter starting register address
		- if speed test only, enter 1 (and mount a 800 BPI skew tape) for all others enter a 0 - program will begin timing functions.
		  On completion the processor will halt.
		- To repeat test, press continue.

	SWITCH SETTINGS:
		None.

ZTSF - TS03/TMA11/TMB11 supplemental instruction test

	ABSTRACT:
		This program is intended to be used in addition to the TM11/TU10 instruction test (DZTMA).
		It only checks the data transfers at odd byte address and operation incomplete time out.

	HARDWARE REQUIREMENTS:
		PDP-11 computer with 4KW of memory, TMA11 or TMB11 control unit and 1-2 tape units

	OPERATING PROCEDURES:
		200 start program
		210 restart program
		- load program into memory
		- place desired tape unit on-line at loadpoint
		- load address 200
		- set console switches to desired test sequence
		- press start
		- program will type identification header then request for unit# (0=default) to test

	SWITCH SETTINGS:
		SW 15=1   (100000)   halt on error
		SW 14=1   ( 40000)   loop on error
		SW 13=1   ( 20000)   inhibit error printouts
		SW 12=1   ( 10000)   inhibit iterations
		SW 11=1   (  4000)   continuous cycle
		SW 10=1   (  2000)   halt after current test
		SW 2-0=1             select test number (1-4) (0=all)

	RUN TIME:
		Approx. 1,25 minutes.