ZTUI - TU45/TM02 Data Reliability test

	ABSTRACT:
		This program will test all tape drive functions such as writing, reading, rewinding, tape positioning, EOT-BOT sensing and
		assumes a good RH and TM02.
		This program has no fixed parameters.

	HARDWARE REQUIREMENTS:
		PDP-11 with 8KW of memory, TM02 controller and 1-8 TU45

	OPERATING PROCEDURES:
		Start/restart addresses:
			200 initial start, all parameters
			204 restart, last pattern used
			210 restart, original pattern
			240 auto-sequence
			300 restart, short parameter list
			- load and start program at 200
			- set desired switches
			- answer the questions:
				REGISTER START: 172440
				VECTOR ADDRESS: 224
				DRIVE NUMBER: (0-7)
				SLAVE NUMBER: (0-7)
				DENSITY: (0-4)3=800BPI, 4=1600 BPI
				PARITY: (0 or 1) 0=ODD 1=EVEN
				FORMAT: (14 or 15)14=NORMAL 15=CORE DUMP
				SLAVE NUMBER: (0-7) IF NO MORE JUST CR
				RECORD COUNT: 100  (1-177777)
				CHARACTER COUNT: 200  (20-4000)
				PATTERN NUMBER: 1 (0-15)
				TAPE MARK=0  (0 or 1)
				SINGLE PASS=0 (0 or 1)
				ENTER STALLS
					- READ=1         }
					- WRITE=1        } (1-177777) EACH INCREMENT is 2.6 µSec
					- TURN AROUND=1  }

	SWITCH SETTINGS:
		SW 15  =1   halt on error
		SW 14  =1   print statistics
		SW 13  =1   dont check data errors
		SW 12  =1   dont check write status
		SW 11  =1   dont check read status
		SW 10  =1   dont print errors
		SW 09  =1   rewind all tapes
		SW 08  =1   random data
		SW 07  =1   random character count
		SW 06  =1   random record count
		SW 05  =1   yozzle current record
		SW 04  =1   do retries
		SW 03  =1   dont read forward
		SW 02  =1   dont read reverse
		SW 01  =1   read forward first
		SW 00  =1   dont write

	NOTES:
		Recommended switch settings SW4,6,7,8 to randomize test and get information about bad spots.

ZTUJ - TU45/TM02 Basic Function test

	ABSTRACT:
		This program will test all of the basic operations of the TU45/TM02 mag tape system.
		All functions: read, write, space, erase, rewind, etc. will be tested and as far as possible some of the RH11 functions.

	HARDWARE REQUIREMENTS:
		PDP-11 with 8KW of memory, TM02 controller and one TU45.

	OPERATING PROCEDURES:
		Start/restart addresses:
			200 start
			210 restart
			- tape unit must be loaded at BOT and on-line
			- load and start program at 200
			- set desired switches
			- answer the questions:

				REGISTER START: 172440
				VECTOR ADDRESS: 224
				DRIVE NUMBER: (0-7)
				SLAVE NUMBER: (0-7)
				RH11 OR RH70: (RH11=0, RH70=1)
				RH ONLY: (0 or 1)
				NRZ ONLY: (0 or 1)

	SWITCH SETTINGS:
		SW 15  =1   halt on error
		SW 14  =1   loop on error
		SW 13  =1   dont print errors
		SW 12  =1   inhibit iterations
		SW 11  =1   continuous cycle
		SW 10  =1   halt after current test
		SW 04-00    select test # (1-24) 0=ALL

ZTUK - TU45/TM02 Control Logic test

	ABSTRACT:
		This program will test all control logic (test 1-41 and 57-64) and data formatting (test 42-56) within the TM02 formatter.
		This program has no fixed parameters.

	HARDWARE REQUIREMENTS:
		PDP-11 with 8KW of memory, TM02 controller and one TU45.

	OPERATING PROCEDURES:
		Start/restart addresses :
			200 start
			210 restart
			- tape unit must be loaded at BOT and on-line
			- load and start program at 200
			- set desired switches
			- answer the questions:

				REGISTER START: 172440
				VECTOR ADDRESS: 224
				DRIVE NUMBER: (0-7)
				DRIVE NUMBER: (0-7) if no more just CR
				SLAVE NUMBER: (0-7)
				SLAVE NUMBER: (0-7) if no more just CR
				NRZ ONLY: (0 or 1)
				STATIC TEST ONLY (0 or 1)

	SWITCH SETTINGS:
		SW 15  =1   halt on error
		SW 14  =1   loop on error
		SW 13  =1   dont print errors
		SW 12  =1   inhibit iterations
		SW 11  =1   continuous cycle
		SW 10  =1   halt after current test
		SW 09  =1   manual intervention test
		SW 08  =1   inhibit wrap data checks
		SW 07  =1   inhibit wrap status checks
		SW 06  =1   selectable wrap data pattern (single test)
		SW 05  =1   select test # (1-64) 0=ALL

	RUN TIME :
		With iterations approx 3 min., without approx 30 sec.

ZTUL - TU45/TM02 Drive Function Timer

	ABSTRACT:
		This program will check both the logic generated time delays and the distances travelled by the tape in response.
		Actual tape speed may also be checked by using the speed tests with an 800 BPI skew tape.

	HARDWARE REQUIREMENTS:
		PDP-11 with 4KW of memory, TM02 controller and 1-8 TU45.

	OPERATING PROCEDURES:
		Start/restart address : 200
		- load and start program at 200
		- set desired switches
		- answer the questions:
			TYPE FIRST ADDRESS CONTROLLER: 172440
			TYPE TM02 DRIVE #'S TO BE TESTED: 0 (0-7)
			FOR TM02 DRIVE0-TYPE SLAVE #'S TO BE TESTED: 0 (0-7)
			TAPE SPEED TESTS ONLY: (YES/NO=1/0) 0
			NRZ ONLY: (YES/NO= 1/0)
		- THE PROGRAM WILL BEGIN TIMING FUNCTIONS.
		- ON COMPLETION THE PROCESSOR WILL HALT.
		- TO REPEAT TEST, PRESS CONTINUE.

	SWITCH SETTINGS:
		SW 15  =1   halt on error
		SW 14  =1   loop current test
		SW 13  =1   inhibit error printout
		SW 11  =1   inhibit iterations
		SW 10  =1   dont print function times
		SW 09  =1   bell on error
		SW 07  =1   halt after selected test
		SW 06  =1   continuous cycle
		SW 05-00    select test # (1-32) 0=ALL

	NOTES:
		If speed tests are selected a master skew tape must be used.